Additional functions
#ACHSE | |
#ACS ON / OFF | Definition/activation of a fixture adaptive coordinate system |
#ADD | |
#AX DEF | Definition of an axes configuration (extended syntax) |
#AX DEF DEFAULT | Loading of default axes configuration (extended syntax) |
#AX REQUEST | Requesting of axes (extended syntax) |
#AX RELEASE | Releasing of axes (extended syntax) |
#AX RELEASE ALL | Releasing of all axes (extended syntax) |
#BACKWARD STORAGE CLEAR | |
#BLOCKSEARCH LOCKED / RELEASED | |
#CALL AX | Requesting of axes |
#CAX | |
#CAX OFF | |
#CAXTRACK ON/OFF | |
#CLEAR CONFIG | |
#COMMENT BEGIN / END | |
#CONTOUR MODE | |
#CONTROL AREA START / END | |
#CONTROL AREA ON / OFF | |
#CONTROL AREA CLEAR | |
#CS ON/ OFF | |
#CYL | |
#CYL OFF | |
#DELETE | |
#DRIVE WR SYN / WAIT SYN | |
#ECS ON / OFF | |
#ENABLE AX LINK / | |
#ERROR | |
#EXPL SYN | |
#FACE | |
#FACE OFF | |
#FGROUP | |
#FGROUP ROT | |
#FGROUP WAXIS | |
#FILENAME | |
#FILTER | |
#FLUSH | |
#FLUSH CONTINUE | |
#FLUSH WAIT | |
#FREE TOOL CHANGE ON / OFF | |
#GET IPO OFFSET | |
#GET WCS POSLIMIT | |
#HSC ON / OFF | |
#IDENT WR / RD / SYN | |
#IF / ELSE / ENDIF | |
#INIT MAKRO TAB | |
#KIN ID | |
#LOAD CONFIG | |
#MACHINE DATA | |
#MAIN SPINDLE | |
#MCS ON / OFF | |
#MCS TO WCS | Transformation of machine coordinate into workpiece coordinate |
#MEAS MODE | |
#MEAS | |
#MSG | |
#MSG INFO | |
#MSG SAVE | |
#OPTIONAL | |
#OVERRIDE | |
#PSET / | |
#PTP ON / OFF | |
#PUT AX | Releasing of axes |
#PUT AX ALL | Releasing of all axes |
#ROTATION ON / OFF | |
#RTCP ON/ OFF | Selection/deselection of rotation tool center point (old syntax) |
#SAVE CONFIG | |
#SET ASPLINE MODE | |
#SET ASPLINE STARTTANG | |
#SET ASPLINE ZIELTANG | |
#SET AX | Definition of an axes configuration |
#SET AX LINK |
Parametering of corner feed reduction
#SET DEC LR SOLL | |
#SET HR | |
#SET IPO SOLLPOS | |
#SET JOG | |
#SET OFFSET | |
#SET SLOPE PROFIL | |
#SET SPLINETYPE AKIMA | Selection of Akima-Spline |
#SET SPLINETYPE BSPLINE | Selection of B-Spline |
#SET TANGFEED RMIN | |
#SET TIP | |
#SIGNAL | |
#SIGNAL REMOVE | |
#SUPPRESS OFFSETS | |
#TIME | |
#TIMER | |
#TLC ON/ OFF | Selection/deselection of tool length compensation |
#TOOL DATA | |
#TOOL LIFE READ / REMOVE | |
#TOOL ORI CS | |
#TOOL PREP | |
#TOOL REFRESH | |
#TRAFO ON/ OFF | |
#TRANSVELMIN ON / OFF |
#VECTORACC ON / OFF | |
#VECTORVEL ON / OFF | |
#VECTOR LIMIT ON / OFF | |
#WAIT | |
#WAIT FOR | |
#WAIT INDP | |
#WAIT INDP ALL | |
#WCS TO MCS | Transformation of workpiece coordinate into machine coordinate |