ID-range 1001750-1001999
1001815 | Initialization of ISG-8-axes hardware version V2 failed. | ||||
| Description |
| |||
Reaction | Class | 3 |
| ||
Solution | Class | 7 |
| ||
Parameter | %1: | Actual value [-] | |||
| |||||
Error type | - | ||||
| |||||
1001816 | Initialization of R&W-hardware failed. | |||
| Description |
| ||
Reaction | Class | 3 |
| |
Solution | Class | 7 |
| |
Error type | - | |||
| ||||
1001817 | Initialization of SERCOS-hardware (ring) failed. | |||
| Description |
| ||
Reaction | Class | 3 |
| |
Solution | Class | 7 |
| |
Error type | - | |||
| ||||
1001818 | Initialization of CIM-hardware failed. | |||
| Description |
| ||
Reaction | Class | 3 |
| |
Solution | Class | 7 |
| |
Error type | - | |||
| ||||
1001819 | No SERCOS hardware configuration but there is a SERCOS axis configured. | |||
| Description |
| ||
Reaction | Class | 3 |
| |
Solution | Class | 7 |
| |
Error type | - | |||
| ||||
1001820 | Driver for ISG hardware selected, but not supported by control. | |||
| Description |
| ||
Reaction | Class | 3 |
| |
Solution | Class | 7 |
| |
Error type | 6, Error message by data transfer into control device. | |||
| ||||
1001821 | Driver for stepper hardware selected, but not supported by control. | |||
| Description |
| ||
Reaction | Class | 3 |
| |
Solution | Class | 7 |
| |
Error type | 6, Error message by data transfer into control device. | |||
| ||||
1001822 | Driver for CIM hardware selected, but not supported by control. | |||
| Description |
| ||
Reaction | Class | 3 |
| |
Solution | Class | 7 |
| |
Error type | 6, Error message by data transfer into control device. | |||
| ||||
1001825 / 1001826 |
| |||
| Description | This error message informs about internal states, error solutions and the place of error in the source. Please give the complete error message data to the CNC manufacturer. | ||
Reaction | Class | 3 |
| |
Solution | Class | 8 | Restart of NC-control necessary. | |
1001827 | Phase switch selected but SERCOS-Ring is not closed. | |||
| Description |
| ||
Reaction | Class | 3 |
| |
Solution | Class | 1 |
| |
Error type | - | |||
| ||||
1001828 |
| |||
| Description | This error message informs about internal states, error solutions and the place of error in the source. Please give the complete error message data to the CNC manufacturer. | ||
Reaction | Class | 3 |
| |
Solution | Class | 8 | Restart of NC-control necessary. | |
1001829 | Initialization of ISG-8-axes hardware version V3 failed. | ||||
| Description |
| |||
Reaction | Class | 3 |
| ||
Solution | Class | 7 |
| ||
Parameter | %1: | Actual value [-] | |||
| |||||
Error type | - | ||||
| |||||
1001830 | Initialization of R&W MCU 3T PCI hardware failed. | |||
| Description |
| ||
Reaction | Class | 3 |
| |
Solution | Class | 7 |
| |
Error type | - | |||
| ||||
1001831 | R&W MCU 3T PCI card found, but not booted. | |||
| Description |
| ||
Reaction | Class | 3 |
| |
Solution | Class | 7 |
| |
Error type | - | |||
| ||||
1001832 | R&W MCU 3T PCI board found and booted, but DPRAM Pointer invalid. | |||
| Description |
| ||
Reaction | Class | 3 |
| |
Solution | Class | 7 |
| |
Error type | - | |||
| ||||
1001833 | Cycle time of R&W MCU 3T PCI board does not match NC cycle time. | |||
| Description |
| ||
Reaction | Class | 3 |
| |
Solution | Class | 7 |
| |
Error type | - | |||
| ||||
1001834 | R&W MCU 3T PCI board: physical HLI address is zero. | |||
| Description |
| ||
Reaction | Class | 3 |
| |
Solution | Class | 7 |
| |
Error type | - | |||
| ||||
1001835 / 1001836 |
| |||
| Description | This error message informs about internal states, error solutions and the place of error in the source. Please give the complete error message data to the CNC manufacturer. | ||
Reaction | Class | 3 |
| |
Solution | Class | 8 | Restart of NC-control necessary. | |
1001837 | Initialization of driver of ISG-8-axes hardware version V3 failed. | ||||
| Description |
| |||
Reaction | Class | 3 |
| ||
Solution | Class | 7 |
| ||
Parameter | %1: | Actual value [-] | |||
| |||||
Error type | - | ||||
| |||||
1001838 | I/O-operation of driver of ISG-8-axes hardware version V3 failed. | ||||
| Description |
| |||
Reaction | Class | 1 |
| ||
Solution | Class | 1 |
| ||
Parameter | %1: | Actual value [-] | |||
| |||||
Error type | - | ||||
| |||||
1001839 | SERCOS-hardware selected, but not supported by control. | |||
| Description |
| ||
Reaction | Class | 3 |
| |
Solution | Class | 7 |
| |
Error type | 6, Error message by data transfer into control device. | |||
| ||||
1001840 | DSE-hardware selected, but not supported by control. | |||
| Description |
| ||
Reaction | Class | 3 |
| |
Solution | Class | 7 |
| |
Error type | 6, Error message by data transfer into control device. | |||
| ||||
1001841 |
| |||
| Description | This error message informs about internal states, error solutions and the place of error in the source. Please give the complete error message data to the CNC manufacturer. | ||
Reaction | Class | 3 |
| |
Solution | Class | 8 | Restart of NC-control necessary. | |
1001842 | No licence for physical drives. | |||
| Description |
| ||
Reaction | Class | 1 |
| |
Solution | Class | 1 |
| |
Error type | - | |||
| ||||
1001843 | Cam table manager: Table file cannot be opened. | |||
| Description |
| ||
Reaction | Class | 1 |
| |
Solution | Class | 1 |
| |
Error type | 5, Error message by access on files. | |||
| ||||