Objects to be parameterized during commissioning

1011:0

Restore default parameters

Restore default parameters

UINT8

RO

0x01 (1_dec)

1011:01

SubIndex 001

If this object is set to "0x64616F6C" in the set value dialog, all backup objects are reset to their delivery state.

UINT32

RW

0x00000000 (0_dec)

8000:0

RTD Settings Ch.1

Maximum subindex

UINT8

RO

0x1B (27_dec)

8000:01

Enable user scale

Activates user scaling

BOOLEAN

RW

0x00 (0_dec)

8000:02

Presentation

Presentation of the measured value

BIT3

RW

0x00 (0_dec)

0

Signed, in two's complement

1

Most significant bit as sign

2

High-resolution (1/100 °C steps)

8000:05

Siemens bits

The S5 bits are displayed in the three low-order bits

BOOLEAN

RW

0x00 (0_dec)

8000:06

Enable filter

Enable filter, which makes PLC-cycle-synchronous data exchange unnecessary

BOOLEAN

RW

0x00 (0_dec)

8000:07

Enable limit 1

Activates limit check for limit 1

BOOLEAN

RW

0x00 (0_dec)

8000:08

Enable limit 2

Activates limit check for limit 2

BOOLEAN

RW

0x00 (0_dec)

8000:0A

Enable user calibration

Activates user calibration

BOOLEAN

RW

0x00 (0_dec)

8000:0B

Enable vendor calibration

Activates vendor calibration

BOOLEAN

RW

0x01 (1_dec)

8000:0E

Swap limit bits

Swaps the two limit bits, in order to achieve compatibility with older hardware versions.

BOOLEAN

RW

0x00 (0_dec)

8000:11

User scale offset

User scaling offset

INT16

RW

0x0000 (0_dec)

8000:12

User scale gain

Gain of the user scaling

INT32

RW

0x00010000 (65536_dec)

8000:13

Limit 1

Value for limit 1

INT16

RW

0x0000 (0_dec)

8000:14

Limit 2

Value for limit 2

INT16

RW

0x0000 (0_dec)

8000:15

Filter settings

Filter settings

UINT16

RW

0x0000 (0_dec)

0

50 Hz

1

60 Hz

2

100 Hz

3

500 Hz

4

1 kHz

5

2 kHz

6

3.75 kHz

7

7.5 kHz

8

15 kHz

9

30 kHz

10

5 Hz

11

10 Hz

8000:16

Calibration interval

reserved

UINT16

RW

0x0000 (0_dec)

8000:17

User calibration offset

User calibration offset

INT16

RW

0x0000 (0_dec)

8000:18

User calibration gain

Gain of the user calibration

UINT16

RW

0x4000 (16384_dec)

8000:19

RTD element

Sensor type

UINT16

RW

0x0000 (0_dec)

0

Pt100

1

Ni100

2

Pt1000

3

Pt500

4

Pt200

5

Ni1000

6

Ni1000 (Siemens)

7

Ni120

8

Resistance measurement with 1/16 ohm resolution

9

Resistance measurement with 1/64 ohm resolution

8000:1A

Connection technology

Connection technology:

UINT16

RW

0x0000 (0_dec)

0

2-wire

1

3-wire

2

4-wire

3

No sensor connected (only supported by hardware version 00):
This setting skips the whole measurement, thus speeding up the data acquisition for the other channels. The green status LED of the respective channel remains lit. The error bit of a deactivated channel is canceled and no longer set.

8000:1B

Wire calibration 1/32 Ohm

Only for 2-wire measurements:
contains the resistance of the supply line for the temperature sensor (in 1/32 ohm).

INT16

RW

0x0000 (0_dec)

8010:0

RTD Settings Ch.2

Maximum subindex

UINT8

RO

0x1B (27_dec)

8010:01

Enable user scale

Activates user scaling

BOOLEAN

RW

0x00 (0_dec)

8010:02

Presentation

Presentation of the measured value

BIT3

RW

0x00 (0_dec)

0

Signed, in two's complement

1

Most significant bit as sign

2

High-resolution (1/100 °C steps)

8010:05

Siemens bits

The S5 bits are displayed in the three low-order bits

BOOLEAN

RW

0x00 (0_dec)

8010:06

Enable filter

Enable filter, which makes PLC-cycle-synchronous data exchange unnecessary

BOOLEAN

RW

0x00 (0_dec)

8010:07

Enable limit 1

Activates limit check for limit 1

BOOLEAN

RW

0x00 (0_dec)

8010:08

Enable limit 2

Activates limit check for limit 2

BOOLEAN

RW

0x00 (0_dec)

8010:0A

Enable user calibration

Activates user calibration

BOOLEAN

RW

0x00 (0_dec)

8010:0B

Enable vendor calibration

Activates manufacturer calibration

BOOLEAN

RW

0x01 (1_dec)

8010:0E

Swap limit bits

Swaps the two limit bits, in order to achieve compatibility with older hardware versions.

BOOLEAN

RW

0x00 (0_dec)

8010:11

User scale offset

User scaling offset

INT16

RW

0x0000 (0_dec)

8010:12

User scale gain

Gain of the user scaling

INT32

RW

0x00010000 (65536_dec)

8010:13

Limit 1

Value for limit 1

INT16

RW

0x0000 (0_dec)

8010:14

Limit 2

Value for limit 2

INT16

RW

0x0000 (0_dec)

8010:15

Filter settings

Filter settings

UINT16

RW

0x0000 (0_dec)

0

50 Hz

1

60 Hz

2

100 Hz

3

500 Hz

4

1 kHz,

5

2 kHz

6

3.75 kHz

7

7.5 kHz

8

15 kHz

9

30 kHz

10

5 Hz

11

10 Hz

8010:16

Calibration interval

reserved

UINT16

RW

0x0000 (0_dec)

8010:17

User calibration offset

User calibration offset

INT16

RW

0x0000 (0_dec)

8010:18

User calibration gain

Gain of the user calibration

UINT16

RW

0x4000 (16384_dec)

8010:19

RTD element

Sensor type

UINT16

RW

0x0000 (0_dec)

0

Pt100

1

Ni100

2

Pt1000

3

Pt500

4

Pt200

5

Ni1000

6

Ni1000 (Siemens)

7

Ni120

8

Resistance measurement with 1/16 ohm resolution

9

Resistance measurement with 1/64 ohm resolution

8010:1A

Connection technology

Connection technology:

UINT16

RW

0x0000 (0_dec)

0

2-wire

1

3-wire

2

4-wire

3

No sensor connected (only supported by hardware version 00):
This setting skips the whole measurement, thus speeding up the data acquisition for the other channels. The green status LED of the respective channel remains lit. The error bit of a deactivated channel is cancelled and no longer set.

8010:1B

Wire calibration 1/32 Ohm

Only for 2-wire measurements:
contains the resistance of the supply line for the temperature sensor (in 1/32 ohm).

INT16

RW

0x0000 (0_dec)

8020:0

RTD Settings Ch.3

Maximum subindex

UINT8

RO

0x1B (27_dec)

8020:01

Enable user scale

Activates user scaling

BOOLEAN

RW

0x00 (0_dec)

8020:02

Presentation

Presentation of the measured value

BIT3

RW

0x00 (0_dec)

0

Signed, in two's complement

1

Most significant bit as sign

2

High-resolution (1/100 °C steps)

8020:05

Siemens bits

The S5 bits are displayed in the three low-order bits

BOOLEAN

RW

0x00 (0_dec)

8020:06

Enable filter

Enable filter, which makes PLC-cycle-synchronous data exchange unnecessary

BOOLEAN

RW

0x00 (0_dec)

8020:07

Enable limit 1

Activates limit check for limit 1

BOOLEAN

RW

0x00 (0_dec)

8020:08

Enable limit 2

Activates limit check for limit 2

BOOLEAN

RW

0x00 (0_dec)

8020:0A

Enable user calibration

Activates user calibration

BOOLEAN

RW

0x00 (0_dec)

8020:0B

Enable vendor calibration

Activates vendor calibration

BOOLEAN

RW

0x01 (1_dec)

8020:0E

Swap limit bits

Swaps the two limit bits, in order to achieve compatibility with older hardware versions.

BOOLEAN

RW

0x00 (0_dec)

8020:11

User scale offset

User scaling offset

INT16

RW

0x0000 (0_dec)

8020:12

User scale gain

Gain of the user scaling

INT32

RW

0x00010000 (65536_dec)

8020:13

Limit 1

Value for limit 1

INT16

RW

0x0000 (0_dec)

8020:14

Limit 2

Value for limit 2

INT16

RW

0x0000 (0_dec)

8020:15

Filter settings

Filter settings

UINT16

RW

0x0000 (0_dec)

0

50 Hz

1

60 Hz

2

100 Hz

3

500 Hz

4

1 kHz,

5

2 kHz

6

3.75 kHz

7

7.5 kHz

8

15 kHz

9

30 kHz

10

5 Hz

11

10 Hz

8020:16

Calibration interval

reserved

UINT16

RW

0x0000 (0_dec)

8020:17

User calibration offset

User calibration offset

INT16

RW

0x0000 (0_dec)

8020:18

User calibration gain

Gain of the user calibration

UINT16

RW

0x4000 (16384_dec)

8020:19

RTD element

Sensor type

UINT16

RW

0x0000 (0_dec)

0

Pt100

1

Ni100

2

Pt1000

3

Pt500

4

Pt200

5

Ni1000

6

Ni1000 (Siemens)

7

Ni120

8

Resistance measurement with 1/16 ohm resolution

9

Resistance measurement with 1/64 ohm resolution

8020:1A

Connection technology

Connection technology:

UINT16

RW

0x0000 (0_dec)

0

2-wire

1

3-wire

2

4-wire

3

No sensor connected (only supported by hardware version 00):
This setting skips the whole measurement, thus speeding up the data acquisition for the other channels. The green status LED of the respective channel remains lit. The error bit of a deactivated channel is canceled and no longer set.

8020:1B

Wire calibration 1/32 Ohm

Only for 2-wire measurements:
contains the resistance of the supply line for the temperature sensor (in 1/32 ohm).

INT16

RW

0x0000 (0_dec)

8030:0

RTD Settings Ch.4

Maximum subindex

UINT8

RO

0x1B (27_dec)

8030:01

Enable user scale

Activates user scaling

BOOLEAN

RW

0x00 (0_dec)

8030:02

Presentation

Presentation of the measured value

BIT3

RW

0x00 (0_dec)

0

Signed, in two's complement

1

Most significant bit as sign

2

High-resolution (1/100 °C steps)

8030:05

Siemens bits

The S5 bits are displayed in the three low-order bits

BOOLEAN

RW

0x00 (0_dec)

8030:06

Enable filter

Enable filter, which makes PLC-cycle-synchronous data exchange unnecessary

BOOLEAN

RW

0x00 (0_dec)

8030:07

Enable limit 1

Activates limit check for limit 1

BOOLEAN

RW

0x00 (0_dec)

8030:08

Enable limit 2

Activates limit check for limit 2

BOOLEAN

RW

0x00 (0_dec)

8030:0A

Enable user calibration

Activates user calibration

BOOLEAN

RW

0x00 (0_dec)

8030:0B

Enable vendor calibration

Activates vendor calibration

BOOLEAN

RW

0x01 (1_dec)

8030:0E

Swap limit bits

Swaps the two limit bits, in order to achieve compatibility with older hardware versions.

BOOLEAN

RW

0x00 (0_dec)

8030:11

User scale offset

User scaling offset

INT16

RW

0x0000 (0_dec)

8030:12

User scale gain

Gain of the user scaling

INT32

RW

0x00010000 (65536_dec)

8030:13

Limit 1

Value for limit 1

INT16

RW

0x0000 (0_dec)

8030:14

Limit 2

Value for limit 2

INT16

RW

0x0000 (0_dec)

8030:15

Filter settings

Filter settings

UINT16

RW

0x0000 (0_dec)

0

50 Hz

1

60 Hz

2

100 Hz

3

500 Hz

4

1 kHz,

5

2 kHz

6

3.75 kHz

7

7.5 kHz

8

15 kHz

9

30 kHz

10

5 Hz

11

10 Hz

8030:16

Calibration interval

reserved

UINT16

RW

0x0000 (0_dec)

8030:17

User calibration offset

User calibration offset

INT16

RW

0x0000 (0_dec)

8030:18

User calibration gain

Gain of the user calibration

UINT16

RW

0x4000 (16384_dec)

8030:19

RTD element

Sensor type

UINT16

RW

0x0000 (0_dec)

0

Pt100

1

Ni100

2

Pt1000

3

Pt500

4

Pt200

5

Ni1000

6

Ni1000 (Siemens)

7

Ni120

8

Resistance measurement with 1/16 ohm resolution

9

Resistance measurement with 1/64 ohm resolution

8030:1A

Connection technology

Connection technology:

UINT16

RW

0x0000 (0_dec)

0

2-wire

1

3-wire

2

4-wire

3

No sensor connected (only supported by hardware version 00):
This setting skips the whole measurement, thus speeding up the data acquisition for the other channels. The green status LED of the respective channel remains lit. The error bit of a deactivated channel is canceled and no longer set.

8030:1B

Wire calibration 1/32 Ohm

Only for 2-wire measurements:
contains the resistance of the supply line for the temperature sensor (in 1/32 ohm).

INT16

RW

0x0000 (0_dec)