Configuration data (0x80n0)

Index 80n0 IO Settings Ch. 1 - 4 (for 0 ≤ n ≤ 3)

Index (hex)	Name	Meaning	Data type	Flags	Default
80n0:0	IO Settings	Max. Subindex	UINT8	RO	0x28 (40_dec)
80n0:04	Device ID	The device ID is used for validating the IO-Link device.	UINT32	RW	0x00000000 (0_dec)
80n0:05	VendorID	The Vendor ID is used for validating the vendor of the IO-Link device.	UINT32	RW	0x00000000 (0_dec)
80n0:20	IO-Link Revision	ID of the specification version based on which the IO-Link device communicates. Bit 0 - 3: MinorRev Bit 4 - 7: MajorRev	UINT8	RW	0x00 (0_dec)
80n0:21	Frame capability	The Frame Capability indicates certain functionalities of the IO-Link device (e.g. ISDU supported). Bit 0: ISDU Bit 1: Type1 Bit 7: PHY1	UINT8	RW	0x00 (0_dec)
80n0:22	Min cycle time	The cycle time refers to the communication between the IO‑Link master and the IO‑Link device. This value is transmitted in the IO‑Link format for Min Cycle Time. Bit 6 and 7: time base Bit 0 to 5: multiplier (see following table)	UINT8	RW	0x00 (0_dec)

Time base	Time base meaning	Calculation	Min. Cycle Time
00_bin	0.1 ms	multiplier x time base	0.0 - 6.3 ms
01_bin	0.4 ms	6.4 ms + multiplier x time base	6.4 - 31.6 ms
10_bin	1.6 ms	32.0 ms + multiplier x time base	32.0 - 132.8 ms
11_bin	6.4 ms	134.4 ms + multiplier x time base	134.4 - 537.6 ms

Index (hex)	Name	Meaning	Data type	Flags	Default
80n0:23	Offset time	Reserved	UINT8	RW	0x00 (0_dec)
80n0:24	Process data in length	These parameters are transmitted in the IO-Link format for “Process data in length”. Bit 7: BYTE indicates whether the value in LENGTH is interpreted as bit length [bit not set] or as byte length + 1 [bit set] Bit 6: SIO indicates whether the device supports the standard I/O mode [bit set] Bit 0 to 4: LENGTH Length of the process data	UINT8	RW	0x00 (0_dec)

Index (hex)

Name

Meaning

Data type

Flags

Default

80n0:23

Offset time

Reserved

UINT8

0x00 (0_dec)

80n0:24

Process data in length

These parameters are transmitted in the IO-Link format for “Process data in length”.

Bit 7: BYTE
indicates whether the value in LENGTH is interpreted

Bit 6: SIO
indicates whether the device supports the standard I/O mode [bit set]

Bit 0 to 4: LENGTH
Length of the process data

UINT8

0x00 (0_dec)

Index (hex)	Name	Meaning	Data type	Flags	Default
80n0:25	Process data out length	These parameters are transmitted in the IO-Link format for “Process data out length”. Bit 7: BYTE indicates whether the value in LENGTH is interpreted as bit length [bit not set] or as byte length + 1 [bit set] Bit 6: SIO indicates whether the device supports the standard I/O mode [bit set] Bit 0 to 4: LENGTH Length of the process data	UINT8	RW	0x00 (0_dec)
80n0:26	Compatible ID	reserved	UINT16	RW	0x0000 (0_dec)
80n0:27	Reserved	reserved	UINT16	RW	0x0000 (0_dec)
80n0:28	Master Control	Controls the IO-Link master port and defines the various operation modes of the IO-Link master. Bits 0...3 0: IO-Link port inactive 1: IO-Link port as digital input port 2: IO-Link port as digital output port 3: IO-Link port in communication via the IO-Link protocol 4: IO-Link port in communication via the IO-Link protocol. IO-Link state is ComStop (no cyclic communication, data is only exchanged when required). Bits 4...15 2: DataStorage active 4: DataStorage upload inactive	UINT16	RW	0x0000 (0_dec)

Index (hex)	Name	Meaning	Data type	Flags	Default
80n8:0	IO Sync Settings	Max. Subindex	UINT8	RO	0x02 (2_dec)
80n8:01	Ratio		UINT16	RW	0x0000 (0_dec)
80n8:05	Offset		UINT16	RW	0x0000 (0_dec)